If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Originally posted by 84jr0 Var inte orolig du får polera upp den innan jag slår sönder den
Åhh, det var skönt att höra. Tack.
:-)
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Så var det dags för hjulinställning imorgon. En polare kommer ställa in min bil men har har aldrig gjort det på en Fiat så han undrade om jag visste var man skruvar camber.
Någon som vet? Annars får han leta upp det när jag lyfter bilen helt enkelt.
Originally posted by 84jr0 Så var det dags för hjulinställning imorgon. En polare kommer ställa in min bil men har har aldrig gjort det på en Fiat så han undrade om jag visste var man skruvar camber.
Någon som vet? Annars får han leta upp det när jag lyfter bilen helt enkelt.
Går inte att skruva Camber. Måste köpa Camberbultar. Finns någon tråd om detta.
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Originally posted by viksson Går inte att skruva Camber. Måste köpa Camberbultar. Finns någon tråd om detta.
Kostar 557:- på mekonomen, priset är per/st tror jag.
Du behöver 2.
Artikel nr. 10-MC112
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Originally posted by 84jr0 Jag ska inte skruva camber ska vara orginal... vill bara ha korrekt inställning så att däcken inte slits på sidorna.
Men du skrev att han undrade över Camber.
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Originally posted by viksson Men du skrev att han undrade över Camber.
Att ändra Camber är ju bra eftersom du har en lägre bil.
Ska jag göra när pengarna räcker till allt. Typ om 100 år.
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Originally posted by viksson Att ändra Camber är ju bra eftersom du har en lägre bil.
Ska jag göra när pengarna räcker till allt. Typ om 100 år.
Du menar på att ställa den negativ? Inget fel att köra orginal jag vill känna på lite skillnad. Vet att den känns bättre i år än förra året men vet inte vad som påverkade mest. Nästa år fixar vi cambern
Originally posted by 84jr0 Du menar på att ställa den negativ? Inget fel att köra orginal jag vill känna på lite skillnad. Vet att den känns bättre i år än förra året men vet inte vad som påverkade mest. Nästa år fixar vi cambern
Nästa år då kör vi!
Click here to visit Raceitaly
______________
Fiat Coupe 20VT Plus -99
Alfa Romeo 156 SW 2.0TS -01 SP3
Chrysler Grand Voyager 3,3l V6
Acura Legend 3,2l V6 -91
SAAB 9000 CSE 2,3T steg2 -98 --SÅLD
"Tappar man ett verktyg kommer det alltid att landa i en balja med spillolja, även om den står flera meter bort."
Murphy´s law.
Originally posted by Freddan72 Det kan inte vara styckpris på de där skruvarna Det blir ju 1100 kr spänn för att justeran cambern till -1.5. Fy fäääään va dyrt.
Sats med 2 inuti. Billigt, mkt billigare än en kränghämmare.
Comment